comments:
Turns out you're right about the quick release latch, but wrong about the replaceable filters. https://www.amazon.com/Particulate-Multipurpose-Reusable-Respirator-65021H1-DC/dp/B002NMFLU2
I always panel line with Tamiya Panel Liner Black while the parts are on the runner. No gloss coat. Never had issues, but I don't think I've ever used Tamiya Panel liner on ABS plastic so best to avoid on ABS no matter what since enamel paints will weaken ABS. You can get around this by applying a topcoat over the ABS parts. If I apply Tamiya panel liner when the kit is assembled I always apply a gloss topcoat to the entire kit before applying panel liner. I also do that when it's a full paint job since the panel liner flows better over a gloss surface. If the kit is unpainted you don't need to apply a gloss coat before applying decals. If the kit is fully painted you should, as a best practice, apply a gloss coat before applying decals. After applying decals I always apply a topcoat no matter what. Decals are very fragile without a topcoat. It's not technically required but you're very likely to scratch off waterslide decals without a topcoat. Also please note that those topcoats you've mentioned are lacquers and will expell very toxic fumes. Spray outside while wearing a proper respirator rated for fumes and particulates. I use this one. There are water-based acrylic top coats out there that are safer to use, but you should still always wear a respirator and if you spray in doors you must make sure the room has proper ventilation.
I'd suggest going a step above that to a P100 mask if you're especially sensitive. This one offers even better protection for about the same price. It's what I use. I found it quite comfortable and easy to get used to.
Here's the one I use.
Have you been touching the resin with your bare hands? Like getting it directly on your skin? Without gloves? Cause yeah that would be super bad. Start by taking a break for at least 6 months, and if the rash reaction is severe go to a doctor and they’ll prescribe steroids. A full body rash is generally considered severe, so maybe just go to urgent care like, first thing in the morning. Also get a cortisone (cortizoid?) cream for your rash. That will speed up healing so much.Also, don’t work where you live. Either work outside or in a garage with the garage at least slightly open. Don’t let those fumes in your house. Don’t cure your pieces inside. The garage is fine because people don’t spend a lot of time in there. When you return to resin:Firstly, get latex free gloves, and many people are allergic to even the latex free ones (me! Slight rash on hands/arms), so if that’s also you just don’t use lotion before putting on gloves and wash your hands with soap afterwards. That’s fully prevented a reaction for me. Second, be wearing goggles. The type you wear in high school science classes. These fumes can cause blindness over time, don’t fuck with your eyesight. Thirdly, get a GOOD mask. A ventilator mask. They’re pricy, but your lungs and overall health are more important (and more expensive to fix if possible). https://a.co/d/0ehd9QmY
recommend this https://www.amazon.com/3M-Respirador-reutilizable-part%C3%ADculas-clasificados/dp/B002NMFLU2/ref=mp_s_a_1_3?crid=1NLVNJG5KBUUG&dib=eyJ2IjoiMSJ9.A8MSkAclqATLhZT2EAKua44xnMsrBeQm3C6B-Bfbxi9L5E3tmwgDMpB_gU1GME_VfOEzFjX77BP10ajVnOtQmo7JPJtjgvNiDP1KRaXM74uUw7GPVHDQClKVq5wxk9y_29DXXCdc4W0PpEa1ccSypfWw35v2sibyNoGk90Y0erzlraI14mkIRsLJxxOVmc5j7mHmDHHyw9D1AVBVeOAShw.3ZgFN8_d3NkDas7maG1f1lY8SPbHtsU6BlU8Gd1sw6c&dib_tag=se&keywords=3m+respirator+mask&qid=1773750962&sprefix=3m+%2Caps%2C200&sr=8-3
It doesn't have to be that expensive if you don't get a full face mask. A half-mask with the NIOSH-approved organic vapor cartridge filters is much cheaper than the full face mask version. https://a.co/d/eV5Uh6N