18AWG 3 Conductor Wire 65.6FT, 18/3 Stranded Tinned Copper Electrical Cable, Flexible Low Voltage Extension Wire for LED Lighting, Automotive Wiring, Marine Electronics and Speaker Systems White

similar products:

BTF-LIGHTING RGBW RGB+Warm White SK6812 (Similar WS2812B) 4 Colors in 1 LED Strip Individually Addressable 16.4ft 60Pixel/m 300LED UL Listed IP65 DC5V White PCB (No Adapter or Controller)

tools, home

DROK 48V Power Supply, AC 110V/220V to DC 0-48V 0-10A 480W Buck Converter, Volt Amp Adjustable Adapter Regulated 5V 12V 24V 30V 36V 48V Volt Switching Voltage LED Transformer Charger for Computer

tools

BTF-LIGHTING 3 Pin 10mm 0.39in Width Transparent Connector Kit,4xGapless Solderless 8PCS Corner Connectors,4PCS 5.9in Long 22AWG Extension Wires,Support WS2812B WS2811 SK6812 SMD LED Strips

tools, home

DC Power Fuse Distribution Strip Module (12 Position, Screw Mount)

tools, home

GLEDOPTO Elite ESP32 WLED LED Strip Light Controller 4 Outputs Ethernet Microphone UART Energy Saving Relay 20A Pluggable Fuse DIY Dynamic for WS2811 WS2812 SK6812 WS2815 Digital Addressable RGB IC

tools, home

comments:

redroguetech posted on r/wled4w

24 volt, definitely. Get waterproof. Short of extreme efforts, channels will not be waterproof. I prefer SK6812, but watch http://youtube.com/watch?v=QnvircC22hU There is no limit to the number of pixels a Gledopto can handle. Where you will need to use a separate output is if you can't get the data line from the end of a prior run to the beginning of the next. In my experience, using Gledopto, 24v LEDs SK6812 (https://www.amazon.com/dp/B01MTW2L6B), 18UAG solid-core wire, the data line cannot exceed about 15 feet from the prior LED (not from the controller). YMMV. I have 65 feet, with about 1200 LEDS, using 350 total feet of wire, and so far no issues. My setup: LEDs: https://www.amazon.com/dp/B01MTW2L6B PSU: https://www.amazon.com/dp/B09NQ4G48H Connectors: https://www.amazon.com/dp/B0B3MH2NK7 Power distribution: https://www.amazon.com/dp/B08PT2LNXL Controller: https://www.amazon.com/dp/B0FZ7MH3C5 -- Not super happy with the controller. I can't get the firmware (WLED) to update, and it does not have a stable connection, which I have not determined is in any way it's fault. It's well made, easy to use, but frankly not sure what it gives that you would not get from a basic ESP32. Wire: I used solid-core thermostat wire for trunk lines. Solid-core is easier to work with for long runs, but should not be used to connect to the LED strips, so I would do it differently and instead use "landscaping" wire, like https://www.amazon.com/dp/B0D5LCJT5T/ I used lots and lots of WAGO connectors with https://www.supplyhouse.com/WAGO-221-2523-3-Gang-Mounting-Carrier-for-Levered-Inline-Splicing-Connectors-Gray, but I was in areas not fully exposed to weather

BTF-LIGHTING RGBW RGB+Warm White SK6812 (Similar WS2812B) 4 Colors in 1 LED Strip Individually Addressable 16.4ft 60Pixel/m 300LED UL Listed IP65 DC5V White PCB (No Adapter or Controller)

tools, home

DROK 48V Power Supply, AC 110V/220V to DC 0-48V 0-10A 480W Buck Converter, Volt Amp Adjustable Adapter Regulated 5V 12V 24V 30V 36V 48V Volt Switching Voltage LED Transformer Charger for Computer

tools

BTF-LIGHTING 3 Pin 10mm 0.39in Width Transparent Connector Kit,4xGapless Solderless 8PCS Corner Connectors,4PCS 5.9in Long 22AWG Extension Wires,Support WS2812B WS2811 SK6812 SMD LED Strips

tools, home

DC Power Fuse Distribution Strip Module (12 Position, Screw Mount)

tools, home

GLEDOPTO Elite ESP32 WLED LED Strip Light Controller 4 Outputs Ethernet Microphone UART Energy Saving Relay 20A Pluggable Fuse DIY Dynamic for WS2811 WS2812 SK6812 WS2815 Digital Addressable RGB IC

tools, home